Procedure used on Klikit RC-2 CD version
From this link, downloaded the file xp3264-7.4.2.111-whql.zip.
Extracted to it's own folder. (In Konqueror, navigated to Downloads folder where zip file is located, right mouse cilcked on zip file, Extract-> Extract to xp3264-7.4.2.111-whql)
Opened a root terminal window (Launch->System->Root Actions->Konsole-Superuser Mode)
Note: By using the "Root Actions" Konsole and Konqueror, "sudo" is not needed
cd'd to the downloaded file folder.
(root@twisted-klikit:/home/rgartin# cd Downloads/xp3264-7.4.2.111-whql)
From the "Konsole" window anything after the # in BOLD minus the ) is the command
ran apt-get to obtain ndiswrapper
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# apt-get install ndiswrapper-common ndiswrapper-utils-1.9)
did an ls -la (lowercase L)
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ls -la)
total 3392
drwxr-xr-x 2 rgartin rgartin 4096 2008-06-21 22:03 .
drwxr-xr-x 4 rgartin rgartin 4096 2008-06-21 22:30 ..
-rw-r--r-- 1 rgartin rgartin 1333248 2008-04-15 00:00 athw.sys
-rw-r--r-- 1 rgartin rgartin 1711072 2008-04-15 00:00 athwx.sys
-rw-r--r-- 1 rgartin rgartin 28633 2008-04-21 07:42 netathw.cat
-rw-r--r-- 1 rgartin rgartin 143470 2008-04-15 00:00 netathw.inf
-rw-r--r-- 1 rgartin rgartin 28661 2008-04-21 07:42 netathwx.cat
-rw-r--r-- 1 rgartin rgartin 194981 2008-04-15 00:00 netathwx.inf
ran ndiswrapper using netathw.inf
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ndiswrapper -i netathw.inf)
opened a root konqueror window (Launch->System->Root Actions->Konqueror-Superuser Mode) and navigated to (/etc/modprobe.d)
opened the "blacklist" file with kwrite and added:
# Atheros AR5007EG (Ubuntu detects it as AR5006EG so we use ndiswrapper...)"
blacklist ath_pci
after the "blacklist eth1394" entry, then saved the file.
then I ran the following ndiswrapper commands:
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ndiswrapper -ma)
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ndiswrapper -mi)
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ndiswrapper -m)
after rebooting, I was able to see wlan0 when using ifconfig -a
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ifconfig -a)
eth1 Link encap:Ethernet HWaddr 00:1B:24:3D:0F:DD
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:16na
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:19:7E:75:DA:1A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17 Memory:8c100000-8c110000
In the "Wireless Assistant" I could see my network (twisted) and another one but could not connect to either one.
Tried configuring "wlan0" using "KNetworkManager" but it wouldn't take.
Upon furhter research, I came across this thread in the Ubuntu forums.
Using the last post on this page as an example, I edited my /etc/network/interfaces file Again, I opened a "root konqueror" window
and navigating to "/etc/network" and opened the "interfaces" file and added the info for my network.
auto wlan0
iface wlan0 inet dhcp
pre-up ifconfig wlan0 down
wireless-essid MY_ESSID
wireless-key WEP_KEY_HERE
wireless-mode managed
saved the file and rebooted my laptop again. When I logged back in, I was wireless finally.
(root@twisted-klikit:/home/rgartin/Downloads/xp3264-7.4.2.111-whql# ifconfig -a)
eth1 Link encap:Ethernet HWaddr 00:1B:24:3D:0F:DD
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:16
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:19:7E:75:DA:1A
inet addr:192.168.2.3 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1597 errors:0 dropped:0 overruns:0 frame:0
TX packets:1559 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1434948 (1.3 MB) TX bytes:322738 (315.1 KB)
Interrupt:17 Memory:8c100000-8c110000
Procedure used on fresh install of Klikit RC-2 DVD version
From this link, downloaded the file xp3264-7.4.2.111-whql.zip.
Extracted to it's own folder. (In Konqueror, navigated to Downloads folder where zip file is located, right mouse cilcked on zip file, Extract-> Extract to xp3264-7.4.2.111-whql)
Opened a root terminal window (Launch->System->Root Actions->Konsole-Superuser Mode)
Note: By using the "Root Actions" Konsole and Konqueror, "sudo" is not needed
cd'd to the downloaded file folder.
opened a root konqueror window (Launch->System->Root Actions->Konqueror-Superuser Mode) and navigated to (/etc/modprobe.d)
opened the "blacklist" file with kwrite and added:
# Atheros AR5007EG (Ubuntu detects it as AR5006EG so we use ndiswrapper...)"
blacklist ath_pci
then I ran the following ndiswrapper commands:
ndiswrapper -ma
ndiswrapper -mi
ndiswrapper -m
after rebooting, I was able to see wlan0 when using “ifconfig -a” and was wireless
Comments (0)
You don't have permission to comment on this page.